Have you been on the lookout for know-how around How to Install a Bathtub?
Installing a bath tub isn't precisely brain surgery, but it does call for strong plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is conveniently accessible, the job can move speedily; if you have to open a wall surface to eliminate the old tub as well as place the new bathtub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and set in the brand-new one. Make certain you have qualified yourself for the job and also fit trying it. Instead of employing a service provider to take over a halfway-completed job, it is much better to think about utilizing one before you start. Chances are you might require a specialist plumber to make tube links.
This write-up will aid you set up a brand-new bathtub in your restroom if you have currently acquired a brand-new tub as well as don't require to change the plan of your previous water system pipes.
Your tools and product list must make up the following:
Preparing for the Installment
Firstly, the sustaining structure supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to prevent stress on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be fitted in its final position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you need to do is separate the water system. After doing so, turn on the faucets to drain any water remaining in the system. The procedure of eliminating the existing faucets can be fairly bothersome because of the limited accessibility that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the staying water that will come from the pipes. As soon as the supply pipelines have been removed, use the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming throughout this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to going on to fit the new taps, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the called for setting. The wood boards are handy in evenly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the bathtub until the spirit level reviews degree.
To mount taps, fit all-time low of the outermost flexible tap adapter to the ideal supply pipe by making a compression sign up with; after that do the very same for the other tap.
Activate the supply of water as well as inspect all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the tub and also examine the overflow outlet and the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as explained in the supplier's instruction manual. Tiling and also securing around the bath tub needs to wait up until the tub has actually been made use of at least once as this will settle it into its last placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in area in between the faucet and also the sink. Protect the tap in place with the manufacturer supplied backnut. When the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The previous kind needs to be attached to the tap ends first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to split a stiff seal, triggering the water to pass through the wall surface between the bathroom and also the tiling, bring about complications with wetness and feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes and also cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water before sealing, to allow for the activity experienced when the tub is in usage. The sealant can fracture relatively very early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently available on the marketplace. It is a good idea to fit the floor tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader on How to Install a Bathtub Yourself, I thought sharing that piece of content was a good idea. You should set aside a second to distribute this blog if you appreciated it. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .
View More